企业动态

搜索:

数控激光切割床的维护与保养方法

人气:11 评论:0 日期:2018-07-09 16:43:37

分享数控激光切割床的维护与保养方法

数控激光切割加工分享数控激光切割床的维护与保养方法

现在很多也都采用数控激光切割加工。整机精度(垂直度,平行度,综合问隙等)测试,必要时调整校正。冲床外观及附件之清洁,检点及机械脚(基础)同紧螺丝,螺帽之锁紧及水平检查必要时调整。润滑给油系统之浦,管路阀等清洁保养及检查。空气系统之气动元件,管路等清洁保养及动作测试检查。

对于数控激光切割床大家也需要进行维护与保养,下面看下数控激光切割床的维护与保养方法。

滑润油脂吐出油量及压力检知功能测试与调整。空气系统之滤清器,给油器调整阀等功能及水份杂质测试检查与必要调整。3。空气压力开关设定值检查及压力检知功能测试与调整。模高指示开关设定值检查与实测值之检查.与调整。

平衡器,j部件拆卸分解,清洁检查及装复调试。使用6000-8000小时维护保养锯牙连杆拆卸分解,清洁保养,检查锯牙及连杆螺纹咬合及磨耗状况,并抛光,打磨咬合面并涂抹润滑脂。滑块总成(球座,押盖。超负荷油压缸,蜗轮,蜗杆等)拆卸分解,清洁保养,问隙调垫及磨耗面,油封检查并重新涂抹润滑油脂。

滑快导轨与导路之问隙量测及磨擦面检查,必要时作调整校正。飞轮轴承等添如手动润滑油脂及管路,接头等检查。平衡气缸动作状况及其机油润滑系统油路,接头等测试检查。马达回路及电器操作回路绝缘阻抗之测试检查。数控激光切割床是采用程序控制系统的一种自动化机床,这种车床加工精度高,加工幅面大,操作也简单,所以它比普通的冲床更多优点,同时也受到大众的青睐。

使用3000-4000小时维护保养光电式安全装置性能之测试及投射角一与区域之测试调整。电气系统之另件外观,触点磨耗.与联线松脱等点检,测试及二度落旋转凸轮开关箱与急停同路功能之测试检查调整。超负荷保护装置之油路清洁,油室清洗,油品换新及压力动作与功能测试调整。主马达v型皮带磨耗及张力状况检查,调整。离刹机构各部件拆卸分解(飞轮不含)清洁保养,间隙榆查调整及装复调试。

模垫拆卸分解及清洁检查各磨耗面与重新涂抹润滑脂后组装试车。模高调整装置之链轮,链条,传动轴,蜗轮蜗杆等另部件有无松脱,异常及链条张力检查.与调整。齿轮传动箱上盖拆卸,内部机件磨损及键位松动状况之检查并进行油槽清洗,润滑油 数控转塔冲床换新及运转状况,噪音,振动测试检查。

传动系统各部位注油点之吐出油量及压力测试.与调整。离刹机构之活塞动作,刹车角度,离刹问隙及米令片麽耗量之测试点检.与必要调整。

Maintenance and maintenance of CNC laser cutting machine

CNC laser cutting processing and maintenance of CNC laser cutting machine

Many laser cutting processes are also used nowadays. The accuracy of the whole machine (perpendicularity, parallelism, synthetic gap, etc.) is tested and adjusted as necessary. The cleaning and checking of the appearance and accessories of the punching machine and the mechanical foot (Foundation) are tightened with the tightening screws, the locking and horizontal checking of the nuts are adjusted when necessary. Cleaning and maintenance of lubricating oil system, pipeline valves, etc. Cleaning and maintenance of pneumatic components and piping for air system.

For CNC laser cutting bed, we also need to carry out maintenance and maintenance. Let's take a look at the maintenance and maintenance methods of CNC laser cutting bed.

Test and adjustment of lubricating oil spit and pressure check function. Air system filter, oil regulator valve and other functions and water impurities testing and necessary adjustment. 3. Air pressure switch setting value check and pressure check function test and adjustment. Check and check the setting value of die height indicating switch.

The balancer, J components are disassembled, cleaned, checked and installed. Use 6000-8000 hour maintenance sawing connecting rod disassembly, cleaning and maintenance, check teeth and connecting rod thread bite and wear condition, and polishing, grinding the bite surface and smearing grease. A slider assembly (a ball seat, a lid. Overloaded oil cylinder, worm gear, worm, etc. are disassembled, cleaned, maintained, the gap adjustment pad and wear surface are checked, the oil seal is checked and the grease is re applied.

Check the gap between the sliding guide and the guide, and check the friction surface. Flywheel bearings and so on, such as manual lubrication grease and pipes, joints and so on. Balance cylinder operation status and oil lubrication system oil circuit, joints and other test checks. Test and check for insulation impedance of motor circuit and electrical operation circuit. CNC laser cutting bed is an automatic machine tool with program control system. This lathe has high processing precision, large processing amplitude and simple operation, so it has more advantages than ordinary punching machine, and it is also favored by the public.

Use 3000-4000 hours to maintain the performance of photoelectric safety device and test the adjustment of projection angle and region. The other parts of the electrical system, the wear and tear of the contact, and the spot check of the line loosening, test and adjustment of the test and test of the function of the two degree falling rotating cam switch box and the emergency stop. The oil circuit of the overload protection device is cleaned, the oil chamber is cleaned, the oil is renewed, and the pressure action and function test are adjusted. Check and adjust the wear and tension condition of the main motor V belt. Disassembly and disassembly of the components of the brake mechanism (flywheel free) cleaning and maintenance, clearance adjustment and installation adjustment.

The die cushion is disassembled, cleaned, cleaned and inspected and reassembled with grease. The other parts of sprocket, chain, drive shaft, worm and worm gear are checked, checked and checked. The upper cover of the gear drive box is dismantled, the wear of the internal parts and the loose key position of the key position are checked and the oil tank is cleaned, the new and running status of the lubricating oil CNC turret punch press, the noise and the vibration test.

The spout and pressure test of each part of the transmission system. The piston action, brake angle, brake clearance and the amount of test for the meter are removed from the brake mechanism.


上一条:如何检查钣金加工产品是否过关?下一条:数控激光切割加工出现问题了怎么解决?
XML 地图 | Sitemap 地图